86-371-86603919
Room 1203, Bldg. B, Zensun International Plaza, Zhengzhou, Henan, China (Mainland)
2 Frame Manual Plexiglass Honey Extractor
Introduction of Honey Extractor
A honey extractor is a mechanical device used in the extraction of honey from honey combs. A honey extractor extracts the honey from the honey comb without destroying the comb. Extractors work by centrifugal force. A drum or container holds a frame basket which spins, flinging the honey out. With this method the wax comb stays intact within the frame and can be reused by the bees.
Bee cover the filled in cekks with wax cap that must be removed( cut by knife, etc.) before centrifugation.
Extractors are either tangential or radial depending on how the frames are put into the basket.
Radial baskets have the top bar of the frame facing outwards while tangential basket have one side of the comb facing outward. Large commercial extractors are radial and rely on the upward slope of the comb cells. This slope allows to extract honey by applying centrifugal force toward the upper edge of the comb(opposite to the direction of gravity while in the hive). The amount of work during extraction is reduced in the radial type because the frames do not have to be turned over to extract the honey from the other side of the comb(however some extractors are capable of turning combs automatically.) Hobbyist extractors can be hand or electric motor powered. If the extractor is hand powered, it often has accelerating gear to spin with less effort.
The smallest extractors hold two frames. The largest commercial extractor holds more than a hundred frames.
During the extraction process the honey is forced out of the uncapped wax cells, runs down teh walls of extractor and pools at the bottom. A tap or honey pump allows for the removal of honey from the extractor. Honey muct be removed in time and always stay below the rotating frames as otherwise it prevents extractor from spinning with sufficient speed.
Types of Honey Extractor
Manual Honey Extractor | Electric Honey Extractor |
Fully Enclosed Gear Box
Pollution Environmental Design Operation safer Rotating more lighter, Smooth Long Lasting to use | Motor, Speed Controller High power design, Higher productivity. New type speed controller, operate speed more stable. With Horizontal motor, widening flat beam, low center of gravity design, safer to operate. |
Double-beam structure Machine more durable Avoid honey contamination caused by grinding | Inner Frame Inner frame using a reversible design, easier to operate, more thorough separation of honey, higher productivity. New processing technology, fully consolidate, polished, easy to clean, more durable for use. |
Inner Frame New processing technology, fully consolidate, polished, easy to clean, more durable or use. | |
Barrel Body Seamless welding technology, more durable to use, safer, more gorgeous. One-step forming convex bottom processing technology which helps honey easy to flow out and durable to use. Transparent plexiglas lis, it is easier to observe the status of honey split, avoid contamination and honey splash. |
Specification of 2 Frame Honey Extractor
2 Frame Honey Extractor | ||
Item | Specification | Packaging |
2 Frame Manual Normal Honey Extractor | Barrel Body:35*75cm Inner Frame:26*45cm Material: Stainless Steel Other: Without Stand Standard Configuration:Hand Crank, Lid Optional: Packaging, honey gate | Carton+foam packaging 41*41*77cm Gross Weight:9KG |
2 Frame Manual Flat Bottom Type B Honey Extractor | Barrel Body:38*78cm Inner Frame:26*45cm/28*45cm Material: Stainless Steel Other: Without Stand, flat bottom Standard Configuration:Hand Crank, Stainless Steel Lid, Packaging Optional: honey gate | Carton+foam packaging 41*41*91cm Gross Weight:11KG |
2 Frame Manual Flat Bottom Type A Honey Extractor | Barrel Body:38*78cm Inner Frame:26*45cm/28*45cm Material: Stainless Steel Other: Without Stand, flat bottom Standard Configuration:Hand Crank, Stainless Steel Lid, Packaging Optional: honey gate(plastic/Stainless Steel) | Carton+foam packaging 41*41*91cm Gross Weight:12KG |
2 Frame Manual Honey Extractor with Silver Stand | Barrel Body:38*61cm Inner Frame:26*45cm Material: Stainless Steel Gear: Transmission Shaft Other:Dropped bottom, Gear Case, stand color(red/Silver) Standard Configuration:Hand Crank, plexiglass Lid, Packaging, Plastic Honey Gate | Carton+foam packaging 41*41*77cm Gross Weight:12KG |
2 Frame Manual Honey Extractor with Red Stand | Barrel Body:38*63cm Inner Frame:26*45cm Material: Stainless Steel Other:Dropped bottom, Gear Case, stand color(red/Silver) Standard Configuration:Hand Crank, plexiglass Lid, Packaging, Plastic Honey Gate Optional: Stainless Steel Honey Gate | Carton+foam packaging 41*41*77cm Gross Weight:14KG |
2 Frame Manual Plastic Honey Extractor | Barrel Body:38*63cm Inner Frame:26*45cm Material: Plastic Other:Flat bottom Standard Configuration:Hand Crank, plastic Lid, Packaging Optional: Honey Gate | Carton+foam packaging 41*41*77cm Gross Weight:6KG |
2 Frame Organic Glass Honey Extractor with Silver Stand | Barrel Body:38*63cm Inner Frame:26*45cm Material: plexiglass Other:Dropped bottom, silver stand Standard Configuration:Hand Crank, plastic Lid, Packaging | Carton+foam packaging 43*43*93cm Gross Weight:13KG Include Stand: 19KG |
2 Frame Electric Honey Extractor with Silver Stand | Barrel Body:38*63cm Inner Frame:26*45cm Material: Stainless Steel Motor:vertical Machine Other: Dropped bottom, stand color(silver/red) Standard Configuration:Hand Crank, Plastic Honey Gate, Packaging, plexiglass lid Optional: Customizable voltage, frequency | Carton+foam packaging 41*41*85cm 220V 120W Gross Weight:17KG |
2 Frame Electric Honey Extractor with Red Stand | Barrel Body:38*63cm Inner Frame:26*45cm Material: Stainless Steel Motor:vertical Machine Other: Dropped bottom, stand color(silver/red) Standard Configuration:Hand Crank, Plastic Honey Gate, Packaging, plexiglass lid Optional: Customizable voltage, frequency | Carton+foam packaging 41*41*85cm 220V 120W Gross Weight:17KG |
Henan Peffer Industrial Co., Ltd. is a family-owned enterprise which located in Zhengzhou Henan province since 1986. We have been dedicated to designing, manufacturing and selling a variety of practical and innovative beekeeping tools, including honey extractor, bee hive, honey comb, frames, bee smoker and so on.
Over past decades, it maintained a continuous development due to its sincerity, reliability, innovation and customer-oriented policy that catering to the needs of end users according to changing trends worldwide. Then company has become a reputable supplier in the field that consequently serving the leading companies over the world.
Accordingly, our mission is to provide continuously developed and good quality beekeeping tools, outstanding servuce and lastest information of market to meet the requirements for our customers.
We sincerely look forward to cooperate you in the near future.
We can supply OEM and Custom-made Service.
Contact Information:
Name: Gwyneth
What's app: 0086 15518158199
Skype:gwyneth805
Welcome send me inquiry in any time, i will reply you ASAP!
1. Q:Sample MOQ?
A: 1 pieces as sample is also ok.
2. Q: How do you ship the goods?
A: For sample, we usually ship by TNT, FEDEX, DHL, etc.
For quantity order we usually by sea.
3. Q:How to pay the payment?
A: We usually receive money by T/T, paypal, Western Union, etc.
4. Q: Can i visit your factory?
A: We welcome every customer visit our company, and if you need pick up and book hotel, please let us know in advance.