86-371-86603919
Room 1203, Bldg. B, Zensun International Plaza, Zhengzhou, Henan, China (Mainland)
4 Frames Manual Reversible Honey extractor
Introduction of Honey Extractor
A honey extractor is a mechanical device used in the extraction of honey from honey combs. A honey extractor extracts the honey from the honey comb without destroying the comb. Extractors work by centrifugal force. A drum or container holds a frame basket which spins, flinging the honey out. With this method the wax comb stays intact within the frame and can be reused by the bees.
Bee cover the filled in cekks with wax cap that must be removed( cut by knife, etc.) before centrifugation.
Extractors are either tangential or radial depending on how the frames are put into the basket.
Radial baskets have the top bar of the frame facing outwards while tangential basket have one side of the comb facing outward. Large commercial extractors are radial and rely on the upward slope of the comb cells. This slope allows to extract honey by applying centrifugal force toward the upper edge of the comb(opposite to the direction of gravity while in the hive). The amount of work during extraction is reduced in the radial type because the frames do not have to be turned over to extract the honey from the other side of the comb(however some extractors are capable of turning combs automatically.) Hobbyist extractors can be hand or electric motor powered. If the extractor is hand powered, it often has accelerating gear to spin with less effort.
The smallest extractors hold two frames. The largest commercial extractor holds more than a hundred frames.
During the extraction process the honey is forced out of the uncapped wax cells, runs down teh walls of extractor and pools at the bottom. A tap or honey pump allows for the removal of honey from the extractor. Honey muct be removed in time and always stay below the rotating frames as otherwise it prevents extractor from spinning with sufficient speed.
Types of Honey Extractor
Manual Honey Extractor | Electric Honey Extractor |
Fully Enclosed Gear Box
Pollution Environmental Design Operation safer Rotating more lighter, Smooth Long Lasting to use | Motor, Speed Controller High power design, Higher productivity. New type speed controller, operate speed more stable. With Horizontal motor, widening flat beam, low center of gravity design, safer to operate. |
Double-beam structure Machine more durable Avoid honey contamination caused by grinding | Inner Frame Inner frame using a reversible design, easier to operate, more thorough separation of honey, higher productivity. New processing technology, fully consolidate, polished, easy to clean, more durable for use. |
Inner Frame New processing technology, fully consolidate, polished, easy to clean, more durable or use. | |
Barrel Body Seamless welding technology, more durable to use, safer, more gorgeous. One-step forming convex bottom processing technology which helps honey easy to flow out and durable to use. Transparent plexiglas lis, it is easier to observe the status of honey split, avoid contamination and honey splash. |
Basic Parameters of 4 Frames Manual Reversible Honey extractor
Brand | Peffer |
Model | Peffer-4MR |
Operation Type | Manual |
Frames | 4 Frames |
Reversible | Accept custom-made |
Material | Stainless Steel(customization is available) |
Barrel Body Dimension (D*H)cm | 67*72cm |
Frame Dimension (L*W)cm | 26*45cm |
Net Weight | 37kg |
packing dimension(L*W*H) | 70*70*91cm |
Frame Type | Stainless Steel Polished Frame |
Crossbeam | Reinforced crossbeam |
Lid | Transparent Plexiglass Lid |
Bottom | One-step forming convex bottom |
Hand Crank | With Hand Crank |
Stand | With Stand |
Honey Gate | With plastic honey gate |
Types of 4 Frames Honey Extractor
4 Frames Honey Extractor | ||
Name | Description | Packaging |
4 Frames with silver stand Manual Honey Extractor | Barrel Body:48*64cm Inner Frame:26*45cm Material: Stainless Steel Gear:transmission shaft Other:dropped bottom Standard Configuration: Packaging, Hand crank, plastic honey gate, plexiglas lid | Carton+foam packaging 52*52*77cm Gross Weight:21KG |
4 Frames with red stand Manual Honey Extractor | Barrel Body:48*64cm Inner Frame:26*45cm Material: Stainless Steel Gear:transmission shaft Other:dropped bottom Standard Configuration: Packaging, Hand crank, plastic honey gate, plexiglas lid | |
4 Frames reversible Manual Honey Extractor | Barrel Body:67*72cm Inner Frame:26*45cm Material: Stainless Steel Gear:transmission shaft Other:dropped bottom, red stand Standard Configuration: Packaging, plastic honey gate, plexiglas lid | Carton+foam packaging 70*70*91cm Gross Weight:42KG |
4 Frames with silver stand Electric Honey Extractor | Barrel Body:48*62cm Inner Frame:26*45cm Material: Stainless Steel Machines: Vertical Machine Other:dropped bottom, Standard Configuration: Packaging, plastic honey gate, plexiglas lid Optional Accessories: Customizable voltage and frequency | Carton+foam packaging 52*52*91cm 220V 120W Gross Weight:26KG |
4 Frames with red stand Electric Honey Extractor | Barrel Body:48*62cm Inner Frame:26*45cm Material: Stainless Steel Machines: Vertical Machine Other:dropped bottom, Standard Configuration: Packaging, plastic honey gate, plexiglas lid Optional Accessories: Customizable voltage and frequency |
Henan Peffer Industrial Co., Ltd. is a family-owned enterprise which located in Zhengzhou Henan province since 1986. We have been dedicated to designing, manufacturing and selling a variety of practical and innovative beekeeping tools, including honey extractor, bee hive, honey comb, frames, bee smoker and so on.
Over past decades, it maintained a continuous development due to its sincerity, reliability, innovation and customer-oriented policy that catering to the needs of end users according to changing trends worldwide. Then company has become a reputable supplier in the field that consequently serving the leading companies over the world.
Accordingly, our mission is to provide continuously developed and good quality beekeeping tools, outstanding servuce and lastest information of market to meet the requirements for our customers.
We sincerely look forward to cooperate you in the near future.
We can supply OEM and Custom-made Service.
Contact Information:
Name: Gwyneth
What's app: 0086 15518158199
Skype:gwyneth805
Welcome send me inquiry in any time, i will reply you ASAP!
1. Q:Sample MOQ?
A: 1 pieces as sample is also ok.
2. Q: How do you ship the goods?
A: For sample, we usually ship by TNT, FEDEX, DHL, etc.
For quantity order we usually by sea.
3. Q:How to pay the payment?
A: We usually receive money by T/T, paypal, Western Union, etc.
4. Q: Can i visit your factory?
A: We welcome every customer visit our company, and if you need pick up and book hotel, please let us know in advance.